香蕉久久久久久狠狠色,久久亚洲欧洲精品,久久九九精品国产综合喷水 ,午夜精品久久久内射近拍高清

SMC(軟 磁復(fù)合材料)鐵芯及高端磁體

news

products

Popular Keywords

contact us

Dongguan Mapioneer new materials co.,ltd

Address: Guangdong Province, Dongguan City, South City Hongfu Road Hong Building, Room 1021

Phone:0769-22818925

Fax:0769-22818793

Contact:Jianming Fang

Telephone:13556622770

Mailbox:effrey186@126.com

Site:http://www.magpioneer.com


The technical requirements of the core punchings

Position: Home >> News >> Company news

The technical requirements of the core punchings

Pubdate:2016-02-22 00:00 source:http://m.456oim.cn Click:

Great job noise. Cold stamping belongs impact work, once for each punch, make a noise issue. Punching workshop is one of the hardest hit noise nuisance. 7, punching speed, pressure, prone to injury. Due to the long mold manufacturing cycle and high manufacturing cost, when the small number of parts, cold stamping process is not economical. Only when mass production, mold manufacturing costs on the cost of the work is very small, cold stamping process became economical and reliable processing methods. Type core punchings core lamination according to different shapes, punching into a circular core punching, fan-shaped punching and poles (spade) punching. In the small AC motors and DC armature iron core are usually circular punching. DC motors and synchronous motors pole core common pole lamination press fit together. Punching core of technical requirements, the size of the bad design to meet the requirements. There are a variety of sizes on core salt tablets, but can be attributed to the internal dimension and with the size of two kinds. Internal dimensions as groove dimensions, vents, and other markers of various aperture and grooves on the pole punching, the general accuracy class H10, higher precision is unnecessary. Because the installation error groove wall and the wall of the hole caused by the irregular punching is much larger than the error itself. To fit with the size dimensions, such as the outer core, inner core circle and the shaft hole or the like with the other parts, the precision level and the process used about. 2, form and position deviation should meet the design requirements. Coaxial with the outer circle shall not exceed the difference between the stator lamination. When scheduled for punching and outside the circle for the first time while punching, its concentricity take 0.04-0.06mm, when it is due to internal and external punched twice, it may be appropriate to relax the concentricity. 3, alveolar to be evenly distributed. Groove indexing to be accurate, the difference between the maximum and the minimum width of the teeth should meet the design requirements. Otherwise, it will lead to an imbalance of the magnetic circuit. 4, punching uniform thickness, almost the entire surface, and punch small burr on the cutting. Burr on small motor stator punching sheet should not exceed 0.05mm. Cast aluminum rotor punching burr should not dry 0.1mm. 5, the insulating layer on the surface should be thin and uniform punching, good dielectric strength, oil and moisture resistant.

Recently Viewed:

s
e
r
v
i
c
e
share
Welcome to our message
Please enter the message content, we will contact you shortly.
Name
Name
Phone
Phone
沈阳市| 轮台县| 扶沟县| 社会| 清新县| 徐州市| 深圳市| 昌图县| 唐海县| 双牌县| 灵寿县| 贡觉县| 丰台区| 陇西县| 余江县| 沙坪坝区| 海丰县| 淮阳县| 辛集市| 依兰县| 嘉定区| 苗栗市| 米泉市| 醴陵市| 阿合奇县| 安康市| 汤原县| 中方县| 北碚区| 康马县| 固原市| 阳高县| 淄博市| 长乐市| 东台市| 伽师县| 靖州| 彩票| 濮阳县| 黄浦区| 平顶山市|